Your local HVAC experts in Elm Grove, WI. From emergency repair to full system replacement, we handle every heating and cooling need.
Browse our full range of heating, cooling, and air quality services available in your area.
A correctly sized heat pump installation eliminates the guesswork of mismatched equipment and undersized ductwork. Our technicians perform load calculations, verify airflow across the evaporator coil, and commission the system to manufacturer specifications for peak efficiency and longevity.
Ductwork problems manifest as uneven room temperatures, excessive dust near registers, and HVAC systems that run continuously without satisfying the thermostat. Technicians identify crushed flex runs, separated joints, and deteriorated mastic seals using pressure testing and visual inspection protocols.
When your AC blows warm air, short cycles, or fails to start, the problem may involve a failed compressor, low refrigerant charge, frozen evaporator coil, or faulty control board. Professional repair identifies the exact fault and restores rated SEER efficiency through precise, manufacturer-guided procedures.
An annual air conditioning tune-up catches refrigerant leaks, worn contactor points, and degraded fan motors before they cascade into compressor damage. Technicians measure temperature differential across the coil, verify amp draws, and confirm proper subcooling to protect your investment.
When your heat pump struggles to maintain temperature or runs continuously without reaching setpoint, the problem often traces to refrigerant leaks, failing capacitors, or degraded reversing valves. Skilled technicians restore rated HSPF and SEER performance through systematic component-level troubleshooting.
Full HVAC installation requires coordination of heating equipment, cooling components, ductwork design, and control systems to deliver efficient comfort at rated capacity. Our technicians perform Manual J and Manual D calculations, size equipment to match your structure, and commission the system to manufacturer standards.
A dryer that takes multiple cycles to dry clothes or feels excessively hot to the touch signals a restricted vent line. Technicians clear lint accumulation using rotary brush systems and compressed air, then verify exhaust velocity meets manufacturer specifications for safe, efficient operation.
A professionally installed mini-split eliminates the energy losses associated with traditional ductwork while providing independent temperature control per zone. Technicians mount indoor heads at optimal height, route linesets with proper insulation, and commission each zone for verified heating and cooling output.
Smart thermostats from Ecobee, Nest, and Honeywell Home offer occupancy sensing, geofencing, and learning algorithms that adapt to your schedule automatically. Our technicians verify system compatibility, install the required wiring, and configure the device for optimal interaction with your specific HVAC equipment.
Comprehensive HVAC inspections cover thermostat operation, ductwork condition, refrigerant levels, electrical connections, and combustion safety. This detailed assessment identifies efficiency losses, safety hazards, and components nearing end of service life before they result in costly emergency repairs.
HVAC emergencies do not follow business hours, and a failed system in extreme temperatures puts your household at risk. Our technicians carry common replacement parts including capacitors, contactors, ignitors, and fan motors to resolve most failures in a single visit and restore comfort fast.
Scheduling professional furnace maintenance each fall ensures your heating system delivers full BTU output without wasting fuel. Technicians inspect the inducer motor, verify pressure switch operation, calibrate gas valve output, and clean the burner assembly for reliable cold-weather performance.
Ductless mini-split systems require specialized diagnostics for inverter-driven compressors, electronic expansion valves, and multi-zone communication boards. Our technicians resolve issues including refrigerant leaks at flare connections, blinking error codes, frozen evaporator coils, and failing fan motors.
Indoor air quality suffers when ductwork harbors years of accumulated particulate matter, allergens, and biological growth. Thorough duct cleaning addresses every branch run, main trunk line, and register boot using agitation tools and high-powered vacuum extraction to restore clean airflow.
Boiler systems demand specialized knowledge of hydronic circuits, expansion tanks, pressure relief valves, and combustion analysis. Our technicians diagnose issues ranging from kettling and low water pressure to faulty zone valves and circulator pump failures across gas, oil, and electric units.
In a village like Elm Grove, word travels fast — and that is exactly how most of our customers find us. KIC Refrigeration has earned the trust of Elm Grove property owners through years of delivering honest system evaluations, quality HVAC installations, and heating and cooling systems that keep families comfortable without inflated utility bills.
We believe the best advertising is a neighbor who stays comfortable all year. That is why every KIC Refrigeration project in Elm Grove, WI is completed to the highest standard, backed by our workmanship warranty and manufacturer guarantees, and supported by a team that answers the phone when you call. Your trust is our most valuable asset.
Built on NATE certification, transparent pricing, and a guarantee that we stand behind.
If the repair does not solve the problem or the installation does not perform to specification, we come back and make it right at no additional cost. Our guarantee covers workmanship, parts, and system performance because half-finished work is not in our vocabulary.
We help you select equipment with the highest SEER2, HSPF2, and AFUE ratings that fit your budget, and we install it to manufacturer specifications so you actually achieve rated efficiency. Proper charge, proper airflow, proper duct sealing — the details that turn rated efficiency into real savings.
You receive a written estimate with itemized parts and labor costs before any work begins, and the final invoice matches. No diagnostic fees hidden in the repair bill, no surprise surcharges — just honest pricing you can verify and trust.
Most service calls are completed the same day you call. Our trucks are stocked with over 200 common parts — capacitors, contactors, ignitors, flame sensors, motors, and control boards — so we resolve the majority of repairs in a single visit without waiting on parts.
Every technician carries EPA Section 608 Universal certification for refrigerant handling — required by federal law for working with R-410A, R-22, R-32, and all regulated refrigerants. Your system is serviced by technicians who handle refrigerants legally and responsibly.
Answers to the heating and cooling questions our customers ask most often.
Heat pumps offer both heating and cooling from a single outdoor unit, making them significantly more energy-efficient than furnaces for moderate climates. A heat pump does not generate heat — it transfers it from outdoor air, which requires far less energy than burning gas or running electric resistance coils. Modern cold-climate heat pumps with variable-speed inverter compressors operate effectively down to minus 15 degrees Fahrenheit, making them viable in most Wisconsin locations. For Elm Grove homeowners with natural gas access, a dual-fuel system — heat pump for primary heating paired with a gas furnace for backup during extreme cold — often provides the best balance of efficiency and performance. Heat pumps also qualify for federal tax credits under the Inflation Reduction Act. KIC Refrigeration evaluates your specific climate zone, insulation levels, and utility rates to determine whether a heat pump, furnace, or dual-fuel system is the smartest investment.
Absolutely. Modern high-efficiency HVAC equipment can reduce heating and cooling costs by 20 to 40 percent compared to systems installed 15 or more years ago. The improvement comes from advances in compressor technology, variable-speed motors, and smarter controls. In Elm Grove, upgrading from a 10-SEER air conditioner to a 16-SEER2 or higher unit delivers substantial monthly savings — the higher the SEER2 rating, the less electricity consumed per BTU of cooling. On the heating side, replacing an 80-percent AFUE furnace with a 96-percent modulating furnace means that 16 cents of every heating dollar previously wasted up the flue now heats your home. Heat pumps offer even greater efficiency, delivering 2 to 4 times more heating energy than they consume in electricity. KIC Refrigeration calculates projected energy savings for any equipment upgrade so you can see the return on investment before making a decision.
HVAC repair costs in Elm Grove typically range from $150 to $500 for minor fixes such as capacitor replacement, contactor swaps, or thermostat wiring issues. Mid-range repairs like blower motor replacement or refrigerant recharging run $500 to $1,200. Major repairs — including compressor replacement, heat exchanger repair, or evaporator coil swap — cost $1,200 to $2,500 or more depending on equipment brand and system type. The final price depends on whether you have a furnace, heat pump, air conditioner, boiler, or ductless mini split, as parts and labor vary significantly between system types. Our NATE-certified technicians diagnose the issue accurately on the first visit, and KIC Refrigeration provides a written estimate with transparent pricing before any work begins. We never charge a diagnostic fee when you proceed with the recommended repair.
Yes. KIC Refrigeration offers flexible financing options for HVAC installations in Elm Grove, WI, including low-interest plans, deferred interest same-as-cash programs, and extended payment terms that make it easier to invest in high-efficiency equipment without a large upfront cost. Approved applicants can often finance a complete system replacement for less than $100 per month. We also help Elm Grove homeowners identify and apply for available financial incentives including utility company rebates on high-efficiency equipment, manufacturer promotional pricing, and federal tax credits such as the 25C Residential Clean Energy Credit which provides up to $2,000 for qualifying heat pump installations and up to $600 for qualifying furnaces and air conditioners. Between financing, rebates, and tax credits, the effective cost of a new high-efficiency HVAC system is often significantly lower than the sticker price.
A comprehensive HVAC inspection from KIC Refrigeration in Elm Grove covers every critical component of your heating and cooling system. Our NATE-certified technician evaluates the heat exchanger for cracks using a combustion analyzer, checks thermostat calibration and wiring, tests all electrical connections for tightness and amperage draw, measures refrigerant pressures against manufacturer specifications, clears the condensate drain line, inspects the blower motor and fan assembly for wear, checks the air filter and evaporator coil condition, tests safety controls including high-limit switches and flame sensors, performs carbon monoxide testing on gas-burning equipment, and measures supply and return airflow temperatures to verify the system is producing its rated BTU output. We also visually inspect accessible ductwork for leaks, damage, and insulation condition. You receive a written report with all findings, photos of any concerns, and prioritized recommendations.
Most HVAC installations, major equipment replacements, and significant ductwork modifications in Elm Grove require a mechanical permit from the local building department. This applies to furnace and air conditioner replacements, heat pump installations, boiler swaps, and new ductless mini split systems. Minor repairs like part replacements and refrigerant recharges typically do not require permits. KIC Refrigeration handles all permitting, code compliance documentation, and scheduling of final inspections on your behalf — you do not need to visit any government office or coordinate with inspectors. Permits exist to ensure your system is installed safely and to code, which protects your home and preserves your equipment warranty. Unpermitted work can create liability issues and complicate future home sales. We ensure every project meets current Wisconsin mechanical codes and International Mechanical Code standards.
Hear what our customers have to say about the quality and reliability of our HVAC work.
"KIC Refrigeration replaced our old window units with a mini split system. Night and day difference in comfort and noise level. Wish we had done it sooner."
"KIC Refrigeration has serviced our commercial HVAC system for two years now. Always professional, always on time. Would not trust anyone else."
"Smart thermostat installation was seamless. They even helped me pick the right model for my system before the appointment. Very consultative approach."
Professional heating and cooling services extending to neighboring cities and towns.